[Zhongbo.com] The glass door is a special kind of door leaf. First of all, its thickness is not enough to be a solid door, and it is not a special-shaped door. In fact, it is a special form of door leaf. Glass door tempered glass and ordinary float glass are generally made of glass with a thickness of 12 mm (mm). The tempered glass is both strong and safe. The glass door can be said to be everywhere, there will be some failures when using the glass door for a long time, how can we repair it? Today, let's take a look at the glass door repair method and tell everyone how to disassemble and assemble the glass door. Glass door repair method: remove the floor spring glass door First step of removing the spring glass door: use a Phillips screwdriver to pry off the small clip stainless steel on the upper corner of the door. Put a soft carpet on the bottom of the door and use a 5mm hex wrench to lower the 2 small screws that fix the small silver iron fitting inside the clip and lift the door. Put a thing under the door and lift the door out of the spring shaft. Lift the door and let it go. The second step of removing the ground spring glass door: remove the stainless steel cover of the glass upper clip and the lower clamp on the door, open the door to the 90 degree positioning point of view, use the east and west sides of the handle to open the door, and hold the door by yourself. The other one uses a 6-pointed spoon to unscrew the fixed bushing on the upper and lower door clamps of the door, and removes the bushing to remove the door. If only the upper door clamp sleeve of the door is taken down, the door slant is tilted a little, and the door can be lifted higher when the position is sufficient, so that the lower door clamp sleeve of the door is not removed. The third step of removing the ground spring glass door: Using the following method, one foot is stepped on the floor spring cover, and a hole can be seen at the top of the door. The hole has a screw that can be loosened with a screwdriver. Place the carpet at the bottom of the door and loosen the screws inside the hole. Usually the screw reveals the hole and the outer shaft of the spring leaf can be disengaged. The door leaf is tilted and lifted obliquely upward to disengage the ground spring shaft. Move the door leaf together with the carpet to the door or the door to facilitate local movement, and the ground spring door is disassembled. Glass door repair: precautions for removing the floor spring glass door When dismantling the glass door, make sure that the grounding spring door has a fitting with a solid door frame (or aluminum frame) that is still fitted with a glass clip, with a solid door frame fitting: open the door to a 90-degree positioning point of view, Use the things to pad the handle to open the lower corner of the door, oneself to hold the door, the other one with a screwdriver to adjust the accessories on the top of the door screws, the screw down, the shaft of the accessories will be up, adjust to a certain height to be able to take the door It's open. When the floor spring body can be completely placed in the ground groove, the solid spring body can be stabilized, but cement can also be used, but the cement solidifies for a longer period of time. Remove the ground spring body, add an appropriate amount of quick-drying powder in the ground tank, stir the water until the viscosity is appropriate, and then put it into the ground spring body, and use a rubber hammer or a wooden block to hit the ground spring with a hammer to make the floor spring You can restore the surface level to the surrounding ground, then take the plumb line to find the spring axis position and fine-tune the spring body. The end of the service life of the ground spring is that the shaft oil leakage and the elastic force are weakened . If the shaft axis of the sun shaft and the ground spring main shaft are not strictly perpendicular to the ground, the movement of the door leaf will bring great torque to the floor spring and increase the main shaft. Wear between the bearing and the shaft causes oil leakage. The spring will inevitably weaken the elasticity after long-term stretching. When performing glass door maintenance, you need to pay special attention to the installation of the spring. As long as the floor spring is installed, the glass door can be used better. Types and identification methods of fabric materials for bedding kits Bedding Set,Bedding Sheet Set,Embroidery Sheet,Quilt Covers Shaanxi Xiaoze Textile Co., Ltd. , https://www.xtsxxzth.com
1. Yarn-dyed pure cotton is easy to shrink. Yarn-dyed pure cotton is a kind of pure cotton fabric, which is woven with warp and weft yarns of different colors. Due to the first dyeing and then weaving, the dye penetration is strong, the color fastness is good, and the different-colored yarn fabrics have a strong three-dimensional sense and unique style, and the bedding is mostly represented by a striped pattern. It has the characteristics of pure cotton fabric, but usually shrinks more.
2. The price of polyester and cotton is affordable. Polyester-cotton brand products generally use polyester-cotton fabrics with a ratio of 65% polyester and 35% cotton. Polyester-cotton is divided into two types: plain weave and twill. The plain weave polyester-cotton fabric has a thin surface, good strength and wear resistance, and has a very small shrinkage rate. In addition, because polyester is not easy to dye, polyester-cotton fabrics are mostly light and light tones, which are more suitable for use in spring and summer. Twill polyester cotton is usually denser than plain weave, so it appears dense and thick, and the surface gloss and hand feel are better than plain weave.
3. Pure cotton is very soft, feels good in hand, is comfortable to use, easy to dye, has a rich variety of patterns, is soft and warm, has strong hygroscopicity and is washable, and has less static electricity. It is a widely used material for chuang tops; , Easy to shrink, poor elasticity, acid and alkali resistance, not suitable for long-term treatment at high temperature above 100 degrees Celsius, so it is best to spray wet cotton products when ironing, easy to iron. If possible, iron the product with a steam iron after each use, and the effect will be better.
4. Jacquard pure cotton is thicker. High-count and high-density jacquard pure cotton fabric has a particularly large warp and weft density and rich weaving changes. Therefore, the fabric feels thick and durable, and has a high surface finish. It is a more advanced type of pure cotton fabric.
5. The silk is the smoothest. The appearance of silk is gorgeous and rich, with natural soft light and flickering effect. It feels comfortable, has high strength, and has better elasticity and moisture absorption than cotton. However, the upper four-piece set made of silk is easy to get dirty. Heat resistance to strong sunlight is worse than cotton. The cross-section of the fiber is a unique triangle, and the reflection of light changes after local moisture absorption, which is easy to form water stains and difficult to eliminate, so silk fabrics should be whitened when ironing.